manufacturer, custom & standard hot extruded shapes, structural stainless, steel angles, tees, channels, i-beams, tubing, hollow bar, pre-forms, forging, machining, fabricating, cold drawing, cold rolling, material-austenitic, ferritic, martensitic stainless steels, nickel alloys, carbon steels, alloy steels, titanium, processor cutting, stretch straightening, de-twisting, shot blasting, bump straightening, extrusion of powder metals

Products & Services

• • Manufacturer
  • Custom & Standard Hot Extruded Shapes
  • Structural Stainless
  • Steel Angles
  • Tees
  • Channels
  • I-beams
  • Tubing
  • Hollow Bar
  • Pre-forms
  • Forging
  • Machining
  • Fabricating
  • Cold Drawing
• • Cold Rolling
  • Material-austenitic
  • Ferritic
  • Martensitic Stainless Steels
  • Nickel Alloys
  • Carbon Steels
  • Alloy Steels
  • Titanium
  • Processor Cutting
  • Stretch Straightening
  • De-twisting
  • Shot Blasting
  • Bump Straightening
  • Extrusion Of Powder Metals

Web Result

AMEREX, Extrusions Cost More than Bar Stock

Net Cost of Extrusions Less than Bar Stock Depending upon the steel grade, the difference in final cost between an extrusion and a part made by machining can be enlightening. Look at the part depicted below made from grade 304 stainless steel. the finished extruded shape weighs 9 pounds per foot. To machine this part from a rectangular bar would require a bar 1.750" X 5.000". This bar would weigh ...

http://www.amerexprod.com/p3.htm

AMEREX, The Extrusion

Empezamos en el rea de recepcin de materiales primas donde se reciben barras de diversa composicin qumica. Las barras inoxidables son maquinadas de ser necesario al dimetro requerido por la prensa de extrusin de 5.500", 6.850", 7.500", 8.080", o 9.000" con un pelador de barras Medart. La razn de maquinar el dimetro exterior es para remover las imperfecciones del laminador en caliente, asegurando a...

http://www.amerexprod.com/spanish/p201.htm

AMEREX, Extrusions Cost More than Bar Stock

Extrusiones Cuestan mas que Barra de Stock Dependiendo en al grado de acero, la diferencia entre el costo de una extrusin y el de una pieza fabricada sorprende a muchos. Observe la pieza de abajo hecha con acero inoxidable de grado 304. La pieza extruda terminada pesa 9 libras por pie. Para fabricar esta misma pieza de una barra rectangular requiere una barra de 1.75" por 5". Esta barra puede pesa...

http://www.amerexprod.com/spanish/p3.htm

Amerex

En 1951, Babcock & Wilcox instalo la primera prensa Americana hidrulica para extrusin usando el proceso Ugine-Sejournet para la extrusin de acero inoxidable. Esta prensa opero hasta que Babcock & Wilcox decidi salir del negocio de hacer acero en los 1980 s. Ahora esta Amerex. Empezando en 1992, Amerex empez la renovacin de esta prensa de alta velocidad con controles del horno modernizados,...

http://www.amerexprod.com/spanish/p2.htm

AMEREX's Extrusion Capabilities

Amerex's Extrusion Capabilities The shape should fit into a 6.500" circle. Certain exceptions up to 7.500" are possible. The shape should be at least 1/2 square inch in area. Maximum weight of any one finished piece is 375 lb. with a normal length of 28 feet. Extrusion tolerances must be taken into account. Radii and fillets are greater than cold drawn material. Depending on grade, nominal corner ...

http://www.amerexprod.com/p203.htm

Website Links: