Delta Plastics
(559) 535-1332
10513 Road 236
Terra Bella, California,
USA
93270
custom formulator-seismic upgrading technologies. all areas of epoxy technology. sealants/adhesives/coatings/injection materials. over 30 years compounding experience. specialty electronic encapsulant
- Year Established:
- 1986
Products & Services
-
- Seismic Upgrading
- Sizemic Upgrading
- Upgrade
- Retrofit
- Earthquake Repair
- Sealants
- Adhesives
- Coatings
- Injection
- Brick Repair
- Building Repair
- Epoxy
- Resin
- Foam
-
- Structural
- Seismic
- Earthquake
- Restoration
- Bisfoam
- Delta
- Plastics
- Building
- Repair
- Brick
- Masonry
- Masonary
- Conductive Epoxy
Web Result
- CSU Fresno Testing Report
- California State University, Fresno Department of Civil & Geomatics Engineering & Construction Seismic Evaluation of the Performance of Retrofitted and Repaired Brick Walls by Means of Expansive Epoxy Injection Prepared by: A. El-Zeiny, Ph.D., P.E. and J. Larralde, Ph.D., P.E. August 2000 Abstract A pioneer technique to repair un-reinforced brick walls cracked during past seismic events, o...
- BISFOAM-3 A&B
- BISFOAM-3 A&B Delta Plastics Co. has conducted a series of structural tests on our product, BISFOAM-3 A&B expanding epoxy foam. For a technical data sheet on BISFOAM-3 A&B click here. This product is an improved version of our ceramic epoxy foam which was used in 1973 in the Los Angeles City Hall. The LA City Hall Report of prototype testing is available for viewing on our site. This r...
- LOS ANGELES CITY HALL...
- REPORT ON PROTOTYPE TESTING OF REPAIR TECHNIQUES FOR REPAIR OF EARTHQUAKE DAMAGE TO LOS ANGELES CITY HALL EXTERIOR WALLS UNDER CONTRACT DACW09-72-0067 PREPARED FOR LOS ANGELES DISTRICT CORPS OF ENGINEERS PREPARED BY VTN ORANGE COUNTY 2301 CAMPUS DRIVE IRVINE, CALIFORNIA 92664 12 MAY 1972 INDEX SECTION PAGE 1.0 INTRODUCTION 3 2.0 GENERAL 5 2.1 Purpose 5 2.2 Definitions 5 2.3 Existing Wall Condition...
- FEMA 356
- LOOK WHAT WE'RE DOING!! JULY 5, 2002 Delta Plastics is pleased to announce that Dr. Lawrence Reaveley and Dr. Pedro Romero from the Engineering Department of the University of Utah have finished the requested testing of the Bisfoam-3 A&B epoxy foam. The results are that the Bisfoam-3 A&B will meet the requirements of FEMA 356. The increased calculated h/t ratios will allow walls which were...
- bisfoam data sheet
- DELTA FLAME RETARDANT EPICERAMICtm BISFOAM-3 A&B FREONLESS FOAM SYSTEM Delta EPICERAMICtm BISFOAM-3 A&B is a two-component, fast foaming, above 75 F temperature curing epoxy foaming system. The system cures to a low density, rigid, closed cell foam with outstanding non-burning properties and excellent physical properties. The cured foam, when exposed to open flames, will char with little d...
Website Links:
Delta Plastics | BISFOAM-3 A&B | CSU Fresno Testing Report | Delta Plastics Product Page | FEMA 356 | Figure 1-drawing | Figure 2-drawing | Figure 3-drawing | Figure 4-drawing | Figure 5-drawing | Figure 6-drawing | Figure 7-drawing | Figure 8-drawing | Figure 9-drawing | LA City Hall Report | LA TIMES ARTICLE | LOS ANGELES CITY HALL... | request | SERVICES PAGE
Own this business?
Request to update the information